科技论文和演示页面包括了 COMSOL 全球用户年会上所有的用户演示文稿。这些演示文稿介绍了 COMSOL 用户是如何使用 COMSOL Multiphysics 进行创新性研究和产品设计,研究主题涵盖了包括电气、机械、流体和化工等范围广泛的行业和应用领域。您可以使用“快速搜索”来查找与您研究领域相关的演示文稿。

Numerical Study and Simulation in COMSOL Multiphysics of the Dilution Process during Dust Sampling in Dry Machining

B. Wenga-Ntcheping[1], A. Djebara[1], R. Kamguem[1], J. Kouam[1], V. Songmene[1]
[1]University of Quebec-École de Technologie Supérieure, Montreal, Canada

Dilution’s issue during dry machining have raised the interest’s environmental researchers and engineers. In fact, the sampling of dust emitted during ...

Surface Plasmon Resonance

J. Crompton[1], S. Yushanov[1], L.T. Gritter[1], K.C. Koppenhoefer[1]
[1]AltaSim Technologies, Columbus, OH, USA

The resonance conditions for surface plasmons are influenced by the type and amount of material on a surface. Full insight into surface plasmon ...

Simulation of Acoustic Energy Harvesting Using Piezoelectric Plates in a Quarter-Wavelength Straight-Tube Resonator

B. Li[1], J.H. You[1]
[1]Southern Methodist University, Dallas, TX, USA

An acoustic energy harvesting mechanism at low frequency (~200 Hz) using lead zirconate titanate (PZT) piezoelectric cantilever plates placed inside a ...

Modeling of Chloride Transport in Cracked Concrete: a 3-D Image–Based Microstructure Simulation

Y. Lu[1], E. Garboczi[1], D. Bentz[1]
[1]National Institute of Standards and Technology, Gaithersburg, MD, USA

The prediction of concrete materials service life is not easy, because the complex heterogeneous microstructure and the random nature of concrete ...

Multiphysics Modelling of Standing Column Well and Implementation of Heat Pumps Off-Loading Sequence

A. Nguyen[1], P. Pasquier[1], D. Marcotte[1]
[1] Department of Civil, Geological and Mining Engineering, École Polytechnique de Montréal, Montréal, QC, Canada

A fully coupled multiphysics model involving heat transfer and groundwater flow within a SCW and its surrounding ground was implemented in COMSOL ...

Load Cell Design Using COMSOL Multiphysics

A. Marchidan[1], T. Sullivan[1], J. Palladino[1]
[1]Trinity College, Hartford, CT, USA

COMSOL Multiphysics was used to design a binocular load cell. A three-dimensional linear solid model of the load cell spring element was studied to ...

Modeling Microwave Waveguide Components: The Tuned Stub

R.W. Pryor[1]
[1]Pryor Knowledge Systems, Bloomfield Hills, MI, USA

The waveguide device modeled here specifically demonstrates the exploration of a small, but very important, subset of components of the family of ...

Modeling a Combined Photovoltaic-Thermal Panel

E. Gutierrez-Miravete[1], B. Fontenault[2]
[1]Rensselaer Polytechnic Institute, Hartford, CT, USA
[2]General Dynamics-Electric Boat, Groton, CT, USA

A novel combined photovoltaic-thermal panel can simultaneously increase the conversion efficiency of the PV cell and utilize some of the excess thermal ...

Thermal Model for Single Discharge EDM Process Using COMSOL Multiphysics

K. Gajjar[1], U. Maradia[2], K. Wegener[2]
[1]Indian Institute of Technology Bombay, Mumbai, Maharshtra, India
[2]Institute for Process Tools and Manufacturing (IWF), Zurich, Switzerland

Electrical Discharge Machining (EDM) is a non-conventional process used for machining electrically conducting materials. In die sink-EDM, sparks are ...

Optimization of Artificial Diffusion Stabilization Techniques and Corresponding Mesh Density Distribution in Drift Dominated Transport of Diluted Species

J. Jadidian[1], M. Zahn[1], N. Lavesson[2], O. Widlund[2], K. Borg[2]
[1]Massachusetts Institute of Technology, Cambridge, MA, USA
[2]ABB Corporate Research, Västerås, Sweden

This paper presents an optimized combination of artificial diffusion techniques to stabilize a drift dominated streamer discharge model which includes ...

First
Previous
1–10 of 143