Menu

Discussion Forum

New Discussion
查找

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Electrical schematic of electrical circuits

Posted 2021年4月7日 GMT-4 12:57 Electromagnetics, Structural & Acoustics 3 Replies

Sohrab M Piezoelectric, energy harvesting, vibration analysis, vibration control, quartz, crystal resonators
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hi,

I am trying to connect two elements in parallel and then in series with a resistor, ground and circuit. It not clear in COMSOL how are my nodes connected to each other. Is there a way to make a clear map or schematic of the electrical circuit to understand what am I doing?

Thanks in advance

3 Replies Last Post 2021年4月9日 GMT-4 15:32
Dave Greve
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 4 years ago 2021年4月7日 GMT-4 14:52
Updated: 4 years ago 2021年4月7日 GMT-4 14:56

The old-fashioned way is to draw your circuit on a piece of paper and label the nodes.

Comsol does not support schematic capture. You can download free SPICE variants that do schematic capture. Comsol can import a SPICE netlist.

The old-fashioned way is to draw your circuit on a piece of paper and label the nodes. Comsol does not support schematic capture. You can download free SPICE variants that do schematic capture. Comsol can import a SPICE netlist.
Sohrab M Piezoelectric, energy harvesting, vibration analysis, vibration control, quartz, crystal resonators
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 4 years ago 2021年4月7日 GMT-4 16:51

Dave, I appreciate your quick reply.

I need to do more practice then to understand how to understand which node is connected to which node. my circuit is not that complex.

Let's then propose this question as well. Let's imagine I have two separate piezoelectric layers. They are creating voltage. on the electrostatic -> ground : I have boudaries 1, 2 on the electrostatic -> terminal : I have boundaries 3, 4.

My circuit is comprised of : Ground node, resistor , and external terminal. The ground node is p on node 0 The resistor is p on node 1 and n on node 0 The external ternal uses the same node as in electrostatic.

what will be the configuration to connect them in series and parallel? Do I need to swap boudaries on electrostatic?

Dave, I appreciate your quick reply. I need to do more practice then to understand how to understand which node is connected to which node. my circuit is not that complex. Let's then propose this question as well. Let's imagine I have two separate piezoelectric layers. They are creating voltage. on the electrostatic -> ground : I have boudaries 1, 2 on the electrostatic -> terminal : I have boundaries 3, 4. My circuit is comprised of : Ground node, resistor , and external terminal. The ground node is p on node 0 The resistor is p on node 1 and n on node 0 The external ternal uses the same node as in electrostatic. what will be the configuration to connect them in series and parallel? Do I need to swap boudaries on electrostatic?
Sohrab M Piezoelectric, energy harvesting, vibration analysis, vibration control, quartz, crystal resonators
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 4 years ago 2021年4月9日 GMT-4 15:32
Updated: 4 years ago 2021年4月9日 GMT-4 15:32

Ok, Here is a rough schematic of what I am trying to do. (please see attachments)

I understood, since I had 2 bodies but only 1 solid mechanics and 1 electrostatic physics, they were not each working separatly. I made them two separate physics like * solid mechanic1 * electrostatic1 * solid mechanic2 * electrostatic2 * and then * 1 electric circuit.

Would someone please confirm if this is how I should do it?

Thanks.

Ok, Here is a rough schematic of what I am trying to do. (please see attachments) I understood, since I had 2 bodies but only 1 solid mechanics and 1 electrostatic physics, they were not each working separatly. I made them two separate physics like * solid mechanic1 * electrostatic1 * solid mechanic2 * electrostatic2 * and then * 1 electric circuit. Would someone please confirm if this is how I should do it? Thanks.

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content