科技论文和展示

这里您可以找到在全球 COMSOL 年会上所有用户报告的演示文稿。这些演示文稿介绍 COMSOL 用户是如何使用 COMSOL Multiphysics 进行创新性研究和产品设计。研究主题涵盖了包括电气、机械、流体和化工等范围广泛的行业和应用领域。请使用“快速搜索”来查找与您的研究领域相关的演示文稿。

Electric Field Analysis of a Green Rust Surface Treatment Tank for High/Super Alloys

H.K. Yang[1], S.C. Tseng[1]
[1]Institute of Mechanical Engineering, National Yunlin University of Science Technology, Taiwan

In order to perform rust surface treatment for stainless wires, we proposed an electrolyzing equipment to do so. It has the following advantages: safer, cheaper and less environmental pollution. To study the performance of the electrolyzing process, numerical simulation for electric fields will be conducted by using COMSOL Multiphysics software. Taguchi methods was also used to obtain better ...

Resonances in Tapered Double-Port TEM Waveguides

J. Kaerst
HAWK, Fachhochschule Hildesheim/Holzminden/Göttingen, Germany

In this paper resonances in tapered double-port TEM waveguides are used as benchmark for simulations. FEM simulations with COMSOL Multiphysics® and simulations using generalised telegraphist's equations with MATLAB® are compared to ananalytical method capable of calculating the resonances of higher order modes. It is valid for tapered double-port TEM waveguides with constant ...

Superconducting RF Cavity Performance Degradation after Quenching in Static Magnetic Field

I. Terechkine[1], T. Khabiboulline[1], D. Sergatskov[1]
[1]Fermi National Accelerator Laboratory, Batavia, IL, USA

Performance degradation of a superconducting RF cavity after quenching in an external magnetic field was calculated using COMSOL. This degradation is due to the increased resistance of a superconducting surface with trapped magnetic flux. The amount of the trapped flux depends on the size of the normally-conducting opening that develops in the superconducting wall of a cavity during quenching. ...

Mode Conversion Losses in a Smooth Wall Circular Waveguide

R. Kumar[1], H. B. Pandya [1], S. Danani [1], P. Vasu [1], V. Kumar[1]
[1]ITER-India, Gandhinagar, Gujarat, India

The ITER-ECE transmission lines consist of smooth-wall circular waveguides, including miter bends and other components. The performance of the TL is crucial to ensuring that the requirements for the diagnostic to measure the plasma parameters are met. COMSOL Multiphysics® has a finite element method with a built-in Eigenmode matrix solver. The accuracy of COMSOL solutions depends on the size of ...

Complex K-Bands Calculation for Plasmonic Crystal Slabs by Means of Weak Formulation of Helmholtz's Eigenvalue Equation

G. Parisi[1], P. Zilio[1], F. Romanato[1]
[1]University of Padova, Padova, Italy

We present a Finite Element Method (FEM) to calculate the complex valued k(?) dispersion curves of a photonic crystal slab in presence of both dispersive and lossy materials. In particular the method can be exploited to study plasmonic crystal slabs. We adopt Perfectly Matched Layers (PMLs) in order to truncate the open boundaries of the model, including their related anisotropic permittivity and ...

Going beyond Axisymmetry: 2.5D Vector Electromagnetics

Y.A. Urzhumov[1][,][2], N.I. Landy[1][,][2], C. Ciraci[2], D.R. Smith[1][,][2]
[1]Department of Electrical and Computer Engineering, Pratt School of Engineering, Duke University, Durham, NC, USA
[2]Center for Metamaterials and Integrated Plasmonics, Pratt School of Engineering, Duke University, Durham, NC, USA

Linear wave propagation through inhomogeneous structures of size R?? (Fig.1) is a computationally challenging problem, in particular when using finite element methods, due to the steep increase of the number of degrees of freedom as a function of R/?. Fortunately, when the geometry of the problem possesses symmetries, one may choose an appropriate basis in which the stiffness matrix of the ...

Optimization of Mechanical Properties of Superconducting Cavities for Project X LINAC

I. Gonin[1], M. Awida[1], T. Khabiboulline[1], V. Yakovlev[1]
[1]Fermilab, Batavia, IL, USA

Project X is a proposed proton accelerator complex at Fermilab. The CW LINAC is based on five types of resonators operating at three frequencies: half-wave, spoke, and elliptical. The low beam current for the CW operation of Project X requires cavities to operate at a high loaded Q and, thus, narrow bandwidth. Therefore, it requires optimal mechanical design of the cavities to minimize the ...

Optimization of Active Packaging for Microwaveable Food Products Using COMSOL Multiphysics® - new

S. Landa[1], A. Bardenstein[1]
[1]Danish Technological Institute, Taastrup, Denmark

Upon operation, the magnetron of a conventional microwave oven induces a pattern of standing electromagnetic waves in the oven cavity. Interactions with the field define the amount of energy absorbed in a part of a food object within the cavity. The well-known inhomogeneous heating produced in a microwave oven is partially an effect of the standing waves’ natural nodes and antinodes and ...

Micromachined Silicon Integrating Cavities for Far-Infrared Bolometer Arrays - new

M. Audley[1], G. de Lange[1], G. Keizer[1], C. Bracken[2]
[1]SRON Netherlands Institute for Space Research, Groningen, The Netherlands
[2]National University of Ireland, Maynooth, Co. Kildare, Ireland

We are investigating gold-plated micromachined silicon integrating cavities for arrays of far infrared Transition Edge Sensor bolometers. We present the results of our simulations and show how we used COMSOL Multiphysics® software to optimize the geometry of the integrating cavity. We show that we can achieve a high optical efficiency over a wide frequency range.

Microwave Interstitial Tumor Ablation: New Modality for Treatment of Liver Cancer

S. Maini[1] , A. Marwaha[1] , and S. Marwaha[1]

[1] Department of Electrical & Instrumentation Engineering, SLIET , Longowal (Deemed University), Punjab

Hyperthermia is newly back in the interest of both, clinical and research oncologists, because of its properties to directly produce permanent damages of the treated tumors and to elicit important immunological responses against cancer cells by changing their immunogenicity.  Microwave ablation is used in the treatment of primary and secondary tumors of the liver.  Microwave antennas ...

Quick Search