Menu

Discussion Forum

New Discussion
查找

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Large difference between analytical solution and simulation results (error in model setup)

Posted 2011年7月1日 GMT-4 14:24 MEMS & Nanotechnology, MEMS & Piezoelectric Devices, Structural Mechanics Version 4.0a, Version 5.0 6 Replies

Mohamed Aref
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam



Hi all, I'am Mohamed Aref, and want to simulate cMUT and compare results with analytical solution, after setup model and get simulation results, i found large difference between analytical solution and simulation results (error in model setup).

cMUT is simply a parallel plate capacitor and I put voltage on the top plate and ground on button one, see the attached image.

This is the steps i done:
1- Modeling
2- Materials
3- Physics
>> in physics, first calculate force from (Force Calculation) and then set this force as boundary load,

Let's first compare between deformation in membrane due to electrostatic force

>> From analytical deformation at voltage=202 volts equal 0.5 um, and from simulation equal 4*10-11 m
so there is difference by factor 10^-4

I think that is error due to error in force calculation as it depend on the type of dielectric between the to electrodes which is air, as when i modeling the cMUT i can't define that this gap is air.

The model is attached, and i'll wait your replays, Thanks to you.
Best regards.

Attachments:

6 Replies Last Post 2015年4月29日 GMT-4 04:48
Mohamed Aref
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2011年7月3日 GMT-4 19:35
I don't understand how to setup Moving Mesh Physics for my cMUT model
any help please
I don't understand how to setup Moving Mesh Physics for my cMUT model any help please
wag dgsa
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年3月28日 GMT-4 01:19
Dear Mohamed Aref.

Could you send me a copy of your cmut model. i am also doing some research on CMUT simulation by means of COMSOL.

Best regards

mingjun
Dear Mohamed Aref. Could you send me a copy of your cmut model. i am also doing some research on CMUT simulation by means of COMSOL. Best regards mingjun
Sri Pasumarthi
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2014年4月22日 GMT-4 16:48
Hai, have u got the 3D CMUT module? If yes could u please provide me the design procedure I'm working on CMUT too

--
Sri Sairam Pasumarthi
Hai, have u got the 3D CMUT module? If yes could u please provide me the design procedure I'm working on CMUT too -- Sri Sairam Pasumarthi
Shubham Majumdar
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 10 years ago 2015年3月3日 GMT-5 14:48
Hi,
Can you send me the model please? Working on it, but getting errors.

Thanks.
Hi, Can you send me the model please? Working on it, but getting errors. Thanks.
Walter Frei COMSOL Employee

Please login with a confirmed email address before reporting spam

Posted: 10 years ago 2015年3月4日 GMT-5 09:03
Dear Shubham,

For the type of modeling being described in this thread, we would recommend that you use the Electromechanics interface available in the MEMS Module. In particular, the following example is a good place to start with learning this interface:
www.comsol.com/model/electrostatically-actuated-cantilever-444
And then, to see what other types of modeling are possible with the Electromechanics interface, see:
www.comsol.com/model/biased-resonator-models-3d-11748

Please note that the approach described earlier in this thread, of manually combining electrostatics, moving mesh, and solid mechanics is a "legacy" approach and was made obsolete by the Electromechanics interface.

Best Regards
Dear Shubham, For the type of modeling being described in this thread, we would recommend that you use the Electromechanics interface available in the MEMS Module. In particular, the following example is a good place to start with learning this interface: http://www.comsol.com/model/electrostatically-actuated-cantilever-444 And then, to see what other types of modeling are possible with the Electromechanics interface, see: http://www.comsol.com/model/biased-resonator-models-3d-11748 Please note that the approach described earlier in this thread, of manually combining electrostatics, moving mesh, and solid mechanics is a "legacy" approach and was made obsolete by the Electromechanics interface. Best Regards
Dwekat
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 10 years ago 2015年4月29日 GMT-4 04:48
Dear Walter Frei ;
Thank you for such info.
I wonder if the " Electromechanics " interface also valid for non MEMS applications ?

Best Regards ;
Dear Walter Frei ; Thank you for such info. I wonder if the " Electromechanics " interface also valid for non MEMS applications ? Best Regards ;

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content