Menu

Discussion Forum

New Discussion
查找

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

2D surface plot of positive normal stress

Posted 2011年12月7日 GMT-5 04:52 Results & Visualization Version 3.5a 6 Replies

Birgit Palm
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Dear community,

I have an old model in V3.5a (quite big) where I need a special plot for a presentation. I calculated (2D axisymmetric) temperature and stresses and show normal radial stress, which is in a range between 69 and -200 MPa. As I want to have a closer look at the positive stresses, I tried to surface plot the expression "sr_maxi>0[MPa]". Unfortunately the surface plot is now dimensionless and shows a color range between 0 and 1. I need to illustrate the positive stresses as calculated, in MPa - how can I do that? Does anyone have an idea?

Thanks for your help,
Birgit
6 Replies Last Post 2011年12月12日 GMT-5 16:08
Edgar Kaiser
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2011年12月7日 GMT-5 09:35
Birgit,

I think your expression must be sr_maxi*(sr_maxi>0)

This will plot all values > 0 and will plot 0 for negative values.

Maybe just defining a range for the plot would yield the same result?

Cheers
Edgar
Birgit, I think your expression must be sr_maxi*(sr_maxi>0) This will plot all values > 0 and will plot 0 for negative values. Maybe just defining a range for the plot would yield the same result? Cheers Edgar
Birgit Palm
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2011年12月8日 GMT-5 02:37
Dear Edgar,

thanks for your reply.
Using the expression the square stresses [Pa^2] was shown, not what I wanted. But as usual, the simple things work best - just adjusting the range to 0-70 MPa gave me the needed picture. Thanks for the hint - I sometimes tend to think too complicated ;-)

Greetings, Birgit
Dear Edgar, thanks for your reply. Using the expression the square stresses [Pa^2] was shown, not what I wanted. But as usual, the simple things work best - just adjusting the range to 0-70 MPa gave me the needed picture. Thanks for the hint - I sometimes tend to think too complicated ;-) Greetings, Birgit
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2011年12月9日 GMT-5 01:08
Hi

What about trying sr_maxi*(sr_maxi[1/Pa]>0) that should remove the extra Pa unit, and Boolean's work best dimension-less

--
Good luck
Ivar
Hi What about trying sr_maxi*(sr_maxi[1/Pa]>0) that should remove the extra Pa unit, and Boolean's work best dimension-less -- Good luck Ivar
Birgit Palm
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2011年12月12日 GMT-5 10:41
Dear Ivar,

thanks also for your reply - I just tried your option and it worked - the stress is shown in MPa. Although the edition of the range has the advantage that everything below 0 is left blank and only stresses above 0 MPa is colored, whereas your suggestion already displays 0 MPa in dark blue. The option with everything blank besides >0 MPa is a bit clearer for looking at the overview.

Best regards,
Birgit
Dear Ivar, thanks also for your reply - I just tried your option and it worked - the stress is shown in MPa. Although the edition of the range has the advantage that everything below 0 is left blank and only stresses above 0 MPa is colored, whereas your suggestion already displays 0 MPa in dark blue. The option with everything blank besides >0 MPa is a bit clearer for looking at the overview. Best regards, Birgit
Edgar Kaiser
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2011年12月12日 GMT-5 10:47
Hi Ivar,

I find it a little funny (or isn't it strange?) that a boolean expression returns a unit? I am wondering if this is consistent from mathematical point of view.

Cheers
Edgar
Hi Ivar, I find it a little funny (or isn't it strange?) that a boolean expression returns a unit? I am wondering if this is consistent from mathematical point of view. Cheers Edgar
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2011年12月12日 GMT-5 16:08
Hi Edgar

I do agree with you, but that is the only explanation I can come to if there is a ^2 on the units, or there are something more on the line not shown. I havent rechecked, I mostly make my variables without units to enter a boolean expression, but in some fields its not possible, it flags an error, it seemsthat units are not accepted systematically and everywhere. Anyhoe I do not have 3.5 running anymore so I cannot check either ;)

--
Good luck
Ivar
Hi Edgar I do agree with you, but that is the only explanation I can come to if there is a ^2 on the units, or there are something more on the line not shown. I havent rechecked, I mostly make my variables without units to enter a boolean expression, but in some fields its not possible, it flags an error, it seemsthat units are not accepted systematically and everywhere. Anyhoe I do not have 3.5 running anymore so I cannot check either ;) -- Good luck Ivar

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content