Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Setting pressure point constraint in closed fluid mechanics problem

Shahriar Khushrushahi

Please login with a confirmed email address before reporting spam

Hi

My problem involves a closed sphere filled with magnetic fluid put near a rectangular bar magnet. Physically when this is done there is a pressure build up in the fluid because of the magnetic body force generated and there is no steady state flow.

The magnetic fluid magnetization is kept simple and is described by the linear relation M=Xi *H in the different directions. The volume body force density is given as follows
Fx=Mx*d(Hx,x)+My*d(Hx,y)+Mz*d(Hx,z)
Fy=Mx*d(Hy,x)+My*d(Hy,y)+Mz*d(Hy,z)
Fz=Mx*d(Hz,x)+My*d(Hz,y)+Mz*d(Hz,z)

The boundary condition on the fluid is no-slip and continuity for the normal magnetic flux density.
If I specify a non-correct pressure then COMSOL gives me a static result of positive flow when this is not physically correct. The problem I am having is I dont know the pressure point constraint that I need to specify so that the problem converges. I would like for the problem to solve the pressure automatically.

I have attached the problem. Any help on this will greatly help me and people with similar problems in closed fluid mechanics problems
Thanks
Shahriar


6 Replies Last Post 2012年10月24日 GMT-4 17:45
COMSOL Moderator

Hello Shahriar Khushrushahi

Your Discussion has gone 30 days without a reply. If you still need help with COMSOL and have an on-subscription license, please visit our Support Center for help.

If you do not hold an on-subscription license, you may find an answer in another Discussion or in the Knowledge Base.


Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年1月19日 GMT-5 15:53
Hi,
I have the same problem, could you find any answer for pressure point condition?
Thanks,
Giti
Hi, I have the same problem, could you find any answer for pressure point condition? Thanks, Giti

Shahriar Khushrushahi

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年1月19日 GMT-5 18:35
It was a long time ago, and I dont remember how I resolved it. I think it shouldnt matter what the pressure is set at any point because the solution will just scale relative to that initial set pressure.
It was a long time ago, and I dont remember how I resolved it. I think it shouldnt matter what the pressure is set at any point because the solution will just scale relative to that initial set pressure.

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年1月19日 GMT-5 19:04
Thanks
Thanks

Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年1月20日 GMT-5 02:02
Hi

as for all physics one need to sett get dependent variables defined fully, in FCD the pressure is often a relative or gauge pressure, and the results are correct for any value + a constant at some time one need to fix this constant and if a p=o output BC is not used, and setting a "p=0" at one point within the fluid domain might be enough to define the constant (=0 in this case)

--
Good luck
Ivar
Hi as for all physics one need to sett get dependent variables defined fully, in FCD the pressure is often a relative or gauge pressure, and the results are correct for any value + a constant at some time one need to fix this constant and if a p=o output BC is not used, and setting a "p=0" at one point within the fluid domain might be enough to define the constant (=0 in this case) -- Good luck Ivar

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年10月24日 GMT-4 07:16
Hi Shahriar Khushrushahi,

i know it was a very long time ago.

could you send me the latest modell about ferromagnetic fluid. Or maybe the modell that has been presented on comsol converece on 2011 with title "Planar Geometry Ferrofluid Flows in Spatially Uniform Sinusoidally Time-varying Magnetic
Fields"

i'm trying to going into these theme but it's very complex.

thank you

best regards
hidayat
Hi Shahriar Khushrushahi, i know it was a very long time ago. could you send me the latest modell about ferromagnetic fluid. Or maybe the modell that has been presented on comsol converece on 2011 with title "Planar Geometry Ferrofluid Flows in Spatially Uniform Sinusoidally Time-varying Magnetic Fields" i'm trying to going into these theme but it's very complex. thank you best regards hidayat

Shahriar Khushrushahi

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年10月24日 GMT-4 17:45
The file was already attached in the first thread of mine



Hi Shahriar Khushrushahi,

i know it was a very long time ago.

could you send me the latest modell about ferromagnetic fluid. Or maybe the modell that has been presented on comsol converece on 2011 with title "Planar Geometry Ferrofluid Flows in Spatially Uniform Sinusoidally Time-varying Magnetic
Fields"

i'm trying to going into these theme but it's very complex.

thank you

best regards
hidayat


The file was already attached in the first thread of mine [QUOTE] Hi Shahriar Khushrushahi, i know it was a very long time ago. could you send me the latest modell about ferromagnetic fluid. Or maybe the modell that has been presented on comsol converece on 2011 with title "Planar Geometry Ferrofluid Flows in Spatially Uniform Sinusoidally Time-varying Magnetic Fields" i'm trying to going into these theme but it's very complex. thank you best regards hidayat [/QUOTE]

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.