Menu

Discussion Forum

New Discussion
查找

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Very High Temperature in Joule Heating Simulation

Posted 2021年6月4日 GMT-4 10:03 Electromagnetic Heating, Low-Frequency Electromagnetics, MEMS & Nanotechnology Version 5.6 3 Replies

Omar Othman
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hi When I am simulating a 3D electrical heater using joule heating physics on comsol I faced a problem that when I am using an electrical potential of 12V the Temperature increase to the 10^6 K. I have tried the examples of comsol about joule heating and I noticed that if I change set V=12V in these example without changing anything on the example they gave me also a Temperature 10^6. If anybody find the solution of this problem please reply! Thank You!

3 Replies Last Post 2021年6月7日 GMT-4 02:46
Jeff Hiller COMSOL Employee

Please login with a confirmed email address before reporting spam

Posted: 3 years ago 2021年6月4日 GMT-4 10:16

Hi Omar,

If a device has a low resistance, applying a 12V voltage drop to it can cause large current densities and therefore a high heat source.

In addition to that, if the boundary conditions or other temperature-limiting mechanisms are such that the device cannot cool efficiently, even a modest heat source can cause the temperature to rise a lot.

So, I would recommend you look at what the resistance of the device is and how realistic your modeling of the thermal BCs is.

Best,

Jeff

-------------------
Jeff Hiller
Hi Omar, If a device has a low resistance, applying a 12V voltage drop to it can cause large current densities and therefore a high heat source. In addition to that, if the boundary conditions or other temperature-limiting mechanisms are such that the device cannot cool efficiently, even a modest heat source can cause the temperature to rise a lot. So, I would recommend you look at what the resistance of the device is and how realistic your modeling of the thermal BCs is. Best, Jeff
Omar Othman
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 3 years ago 2021年6月4日 GMT-4 18:20
Updated: 3 years ago 2021年6月5日 GMT-4 04:52

Hi Jeff,

Thanks for your reply and help! I am using Nichrome as a wire of the electrical heater (Material properties are Add-In from Comsol material properties) and the BC of the thermal BC's is only convection at the all sides (hair=5 w/m2.K and T=25 degC) and still the Temp is 10^4~5. However in real life application (nichrome wires and MgO outline) the heater required approx. V=12.6V and I=3.2A and the resistivity is 4ohm and the maximum Temperature reached is 350 degC with insulator on the boundary. So how can I simulate this heater (with the exact geometry) to get solution close to the real life application without changing the material.

Thank you for your considreation!

Omar

Hi Jeff, Thanks for your reply and help! I am using Nichrome as a wire of the electrical heater (Material properties are Add-In from Comsol material properties) and the BC of the thermal BC's is only convection at the all sides (hair=5 w/m2.K and T=25 degC) and still the Temp is 10^4~5. However in real life application (nichrome wires and MgO outline) the heater required approx. V=12.6V and I=3.2A and the resistivity is 4ohm and the maximum Temperature reached is 350 degC with insulator on the boundary. So how can I simulate this heater (with the exact geometry) to get solution close to the real life application without changing the material. Thank you for your considreation! Omar
Lars Gregersen COMSOL Employee

Please login with a confirmed email address before reporting spam

Posted: 3 years ago 2021年6月7日 GMT-4 02:46

The resistance is not constant. When the temperature increases the resistance increases as well (for metals). You need to include that effect in your model.

-------------------
Lars Gregersen
Comsol Denmark
The resistance is not constant. When the temperature increases the resistance increases as well (for metals). You need to include that effect in your model.

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content