Menu

Discussion Forum

New Discussion
查找

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Eddy current Braking

Posted 2022年10月6日 GMT+8 20:51 Electromagnetics, General, Physics Interfaces Version 6.0 4 Replies

Mohammed Abdelrahim
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hi there,

I am a senior mechanical engineering student working on a project encapsulating an eddy current braking system for cars. I wanted to simulate a rotating aluminum disk at 1000 rpm and an electromagnet that will generate a magnetic field perpendicular to rotation of the disk thus creating an eddy current braking torque. I have created a global ODE to calculate the torque by eddy current. I have tried using the mef (magnetic and electric fields) physics to simulate the process; however, I keep getting a non-converging error message. If you are able to assist, please feel free to view the attached COMSOL file.

Thank you, Mohammed Abdelrahim

4 Replies Last Post 2022年10月12日 GMT+8 00:12
Mark Harradine
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 3 years ago 2022年10月6日 GMT+8 21:14

Not sure if you have seen this blog post, might be helpful...

https://www.comsol.com/blogs/simulating-eddy-current-brakes

Not sure if you have seen this blog post, might be helpful... https://www.comsol.com/blogs/simulating-eddy-current-brakes
Nirmal Paudel Certified Consultant
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 3 years ago 2022年10月7日 GMT+8 04:44

Hi Mohammed,

Your meshing is too course for a software to converge the solution. Please make sure to resolve all the eddy currents that is induced on the disk. The meshing is very important for this type of simulation especially when you have the "Lorentz Term".

Best Regards, Nirmal Paudel, PhD Veryst Engineering

Hi Mohammed, Your meshing is too course for a software to converge the solution. Please make sure to resolve all the eddy currents that is induced on the disk. The meshing is very important for this type of simulation especially when you have the "Lorentz Term". Best Regards, Nirmal Paudel, PhD Veryst Engineering
Mohammed Abdelrahim
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 3 years ago 2022年10月11日 GMT+8 21:30

Not sure if you have seen this blog post, might be helpful...

https://www.comsol.com/blogs/simulating-eddy-current-brakes

Hi Mark,

I saw this blog and followed the instructions. The problem is they are using a permanent magent and the project we are working on is an electromagnet.

>Not sure if you have seen this blog post, might be helpful... > >https://www.comsol.com/blogs/simulating-eddy-current-brakes Hi Mark, I saw this blog and followed the instructions. The problem is they are using a permanent magent and the project we are working on is an electromagnet.
Mohammed Abdelrahim
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 3 years ago 2022年10月12日 GMT+8 00:12

Hi Nirmal,

I was just trying to make the mesh finer but still the results are the same. Can you also clarify what you mean by this statement?

Please make sure to resolve all the eddy currents that is induced on the disk.

Hi Nirmal, I was just trying to make the mesh finer but still the results are the same. Can you also clarify what you mean by this statement? >Please make sure to resolve all the eddy currents that is induced on the disk.

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content