Multiphysics Simulation of Thermoelectric Systems - Modeling of Peltier-Cooling and Thermoelectric Generation
Fraunhofer-Institute for Physical Measurement-Techniques (IPM), Freiburg, Germany
Electro-thermal interaction is commonly considered only as a matter of joule heating. In addition, the Seebeck-, Peltier- and Thompson-Effects are significant in materials with high thermoelectric figure of merit Z. These thermoelectric materials have a high Seebeck-coefficient α, a good electric conductivity σ, and a poor thermal conductivity λ. They have widespread areas of ...
A. Polit, R. Jez
ABB Corporate Research Center, Krakow, Poland
The air gap is one of the most crucial part of magnetic circuits, especially in high-power inductors. It significantly modifies the parameters of magnetic devices by increasing the saturation current, linearizing B-H curve of magnetic circuit and causing a decreasing in the inductance. Therefore the optimal selection of shape and dimensions of the air gap is very important from the design point ...
O. Vogel, and J. Ulm
Proportional solenoids are well-known and used in a wide range of applications today. This paper is about methods of influencing the characteristic force-stroke-curves of magnetic actuators by means of different pole geometries. The conical design of the stator pole which is mostly used to accomplish proportional solenoids is analyzed by both a simple analytic reluctance model and a FEM model ...
Electrical Conductivity Modeling and Validation in Unidirectional Carbon Fiber Reinforced Polymer Composites
P. Banerjee, J. L. Schmidt
Department of Mechanical Engineering and Materials Science, Washington University in St. Louis, St. Louis, MO, USA
Carbon fiber (CF) reinforced polymer composites (CFRP) have begun to replace Al-Zn-Mg alloys in applications which require high strength-to-weight ratios. The anisotropy of CFRP composites is a result of melt crystallized extrusion techniques that impart an inherent directionality to the CFs and the associated material’s properties. Electrical conductivity was modeled across the entire CF ...
S. Meenatchisundaram, S. M. Kulkarni, S. Bhat
Department of Instrumentation and Control Engineering, Manipal Institute of Technology, Manipal, Karnataka, India.
Department of Mechanical Engineering, National Institute of Technology, Surathkal, Karnataka, India.
Piezoresistive pressure sensors have received much attention over the years because of low cost, simple measurement techniques, etc. There is a challenge in design with respect to appropriate positioning, shape and temperature compensation. Different models of piezoresistive pressure sensors are proposed to enhance its sensitivity in terms of output voltage. This paper aims in sensitivity ...
Comparing Isotropic and Anisotropic Brain Conductivity Modeling: Planning Optimal Depth-Electrode Placement in White Matter for Direct Stimulation Therapy in an Epileptic Circuit
L. C. Zaragoza, B. Hondorp, M. A. Rossi
ITESM, Monterrey, Mexico
Rush Medical College, Chicago, IL, USA
Rush University Medical Center, Chicago, IL, USA
The goal of our work was to calculate a patient-specific brain conductivity map for predicting the extent to which direct stimulation therapy can strategically propagate through pathological white matter. Our laboratory developed isotropic and anisotropic human brain finite element method (FEM) models derived from SPGR magnetic resonance imaging (MRI) and diffusion tensor imaging (DTI), ...
V. Bhatt, R.S Rautela, P. Sharma, D.C. Tiwari, and S. Khushu
Institute of Nuclear Medicine & Allied Sciences (DRDO), Delhi, India
The Helmholtz Coil generates a uniform magnetic field. The commercially available large-size Helmholtz coils prove to be very expensive. This paper describes the economical method of designing and construction of a Helmholtz coil. COMSOL Multiphysics AC/DC Module simulated results and actual results were compared in this study. The coil serves as a component in the system for Hyperpolarisation of ...
M. Puskarczyk, R. Jez 
ABB Corporate Research Center, Krakow, Poland
Multilayer planar transformers are widely implemented in power electronic applications. The design process of these elements is complicated due to the complexity of a magnetic circuit and high frequency interactions between windings. Additionally, an analytical approach to the analysis (based on mathematical formulas) can be uncertain. The applied FEM method of the analysis can be a solution to ...
University of Manchester, Manchester, UK
This report mainly discusses the implementation and results of a project proposal, “Modelling using Finite Element Methods”. The report is devoted to implementation, which is a model of an electromagnet. The software tool that is used to model the electromagnet is COMSOL Multiphysics®, a commercial FEA package provided by the University of Manchester, Computer Science School. Additionally, ...
L. Havez, E. Sarraute
LAPLACE, Toulouse, France
The work proposed in this paper deals with the consideration of 3D geometric effects to evaluate the iron losses in magnetic devices used in power electronics. To carry out this work, we rely upon two existing models of iron losses per unit volume calculation ("Steinmetz") currently used in power electronics. We coupled these two models with a finite element magnetic field calculation software, ...