Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.
Flow vector from a 3D solution into 2D
Posted 2016年7月28日 GMT+8 21:09 Computational Fluid Dynamics (CFD), Geometry, Parameters, Variables, & Functions Version 5.2a 3 Replies
Please login with a confirmed email address before reporting spam
Hello,
I have the following problem: I have a 3D simulation of a gas flow in Comsol 5.0. Now I want to add some heating effects, but as the geometry is cylindrical, a 2D axial symmetric model will do as well. How can I incorporate the resulting 3D flow solution (translated into cylindrical coordinates) into another study in 2D? I tried the "extrude" option, but I could not figure it out.
Thanks a lot!
George
I have the following problem: I have a 3D simulation of a gas flow in Comsol 5.0. Now I want to add some heating effects, but as the geometry is cylindrical, a 2D axial symmetric model will do as well. How can I incorporate the resulting 3D flow solution (translated into cylindrical coordinates) into another study in 2D? I tried the "extrude" option, but I could not figure it out.
Thanks a lot!
George
3 Replies Last Post 2016年8月1日 GMT+8 16:01
Please login with a confirmed email address before reporting spam
Posted:
9 years ago
Dear George,
You would like to take a look at the projection methods in COMSOL:
www.comsol.com/blogs/analyze-simulation-results-projection-operators/
Or use the values from a single slice of your 3D geometry using an extrusion if the results of the flow are axi-symmetric as well.:
www.comsol.com/blogs/part-2-mapping-variables-with-general-extrusion-operators/
Best regards,
Frank
You would like to take a look at the projection methods in COMSOL:
www.comsol.com/blogs/analyze-simulation-results-projection-operators/
Or use the values from a single slice of your 3D geometry using an extrusion if the results of the flow are axi-symmetric as well.:
www.comsol.com/blogs/part-2-mapping-variables-with-general-extrusion-operators/
Best regards,
Frank
Please login with a confirmed email address before reporting spam
Posted:
9 years ago
Dear Frank,
Thank you for the reply. I've been looking at these tutorials for quite some time, but it is still unclear for me how to perform this simple task (see attached). Ok, I can assign the extrusion, and then? Where does the data go? I assume I should define a new component, which is 2D axial symmetric. Then, how do I take the data for the new solution to use? Should I define new variables in the new component, such as mod1.ux = mod2.ux ? I get simply zero's for the vector in the 2D component. Can you point me to a tutorial model in the library? I think I'm missing something.
Thanks a lot again,
George
Thank you for the reply. I've been looking at these tutorials for quite some time, but it is still unclear for me how to perform this simple task (see attached). Ok, I can assign the extrusion, and then? Where does the data go? I assume I should define a new component, which is 2D axial symmetric. Then, how do I take the data for the new solution to use? Should I define new variables in the new component, such as mod1.ux = mod2.ux ? I get simply zero's for the vector in the 2D component. Can you point me to a tutorial model in the library? I think I'm missing something.
Thanks a lot again,
George
Attachments:
Please login with a confirmed email address before reporting spam
Posted:
9 years ago
Dear George,
In essence, you make the results from one source of the extrusion available on the destination.
Some tutorials that use this include:
www.comsol.com/blogs/using-general-extrusion-operators-to-model-periodic-structures/
www.comsol.com/blogs/accessing-non-local-variables-with-linear-extrusion-operators/
www.comsol.com/model/turbulent-flow-over-a-backward-facing-step-228
www.comsol.com/model/submodel-in-a-wheel-rim-8517
Best regards,
Frank
In essence, you make the results from one source of the extrusion available on the destination.
Some tutorials that use this include:
www.comsol.com/blogs/using-general-extrusion-operators-to-model-periodic-structures/
www.comsol.com/blogs/accessing-non-local-variables-with-linear-extrusion-operators/
www.comsol.com/model/turbulent-flow-over-a-backward-facing-step-228
www.comsol.com/model/submodel-in-a-wheel-rim-8517
Best regards,
Frank