Menu

Discussion Forum

New Discussion
查找

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Expanding Volume within a Constant Volume

Posted 2011年2月16日 GMT-5 17:40 Fluid & Heat, Microfluidics, Geometry, Modeling Tools & Definitions, Parameters, Variables, & Functions Version 3.5a, Version 4.0, Version 4.1 3 Replies

Jimmy Thai
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hello,

I'd like to know if it's possible to create a balloon model in COMSOL in which there is one inlet but no outlet and the volume expands throughout the simulation. Overall, we are trying to model a balloon (medical device) being filled with a saline solution within a sphere with constant volume. The non-expanding sphere will be representative of a uterus.

What we are looking to find are:

a) The pressure gradient on the balloon model due to the saline solution.
b) The pressure gradient due to the exertion of forces from the inner expanding balloon over time on the outer spherical model's (uterus) wall.

Thanks for your time.
3 Replies Last Post 2011年8月9日 GMT-4 09:25
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2011年2月17日 GMT-5 01:09
Hi

why not ? so long you do not try a "stationary" on a system without equilibrium I do not see what could go wrong.

You should adapt the settings to allow large deformations or hyper elasticity or whatever appropriate material conditions

My only comment use the latest v4 update it much more stable ;)

--
Good luck
Ivar
Hi why not ? so long you do not try a "stationary" on a system without equilibrium I do not see what could go wrong. You should adapt the settings to allow large deformations or hyper elasticity or whatever appropriate material conditions My only comment use the latest v4 update it much more stable ;) -- Good luck Ivar
Dario Rodrigues
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2011年7月25日 GMT-4 15:14
I have a similar problem, but with the bladder. You're able to model the balloon? Did you use the fluid structure interaction module? Or perhaps the laminar flow/solid mechanics/moving mesh?

Thank you so much!

Dario
I have a similar problem, but with the bladder. You're able to model the balloon? Did you use the fluid structure interaction module? Or perhaps the laminar flow/solid mechanics/moving mesh? Thank you so much! Dario
Jonathan Perez
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2011年8月9日 GMT-4 09:25
Dario,

In my experience with COMSOL, I think you will be able to model the expansion of the balloon. all you have to do is constrain your 3D model by holding it in one point so that the other portions of your geometry will have the freedom to move. That's what i did in my 3D simulation with the swelling of rice grain. i used diffusion and structural mechanics.

Jonathan
Dario, In my experience with COMSOL, I think you will be able to model the expansion of the balloon. all you have to do is constrain your 3D model by holding it in one point so that the other portions of your geometry will have the freedom to move. That's what i did in my 3D simulation with the swelling of rice grain. i used diffusion and structural mechanics. Jonathan

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content