Menu

Discussion Forum

New Discussion
查找

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

ion transfer between two phases

Posted 2011年8月29日 GMT-4 16:14 Version 4.2 5 Replies

Xu Zou
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

New user to Comsol and hope someone can help out.

I'm trying to model a process in which a cation transfers from organic phase to aqueous phase when applied a current across the two phases. Then the concentration and potential profiles at the two phases are obtained.

How to model the ion transfer between two phases when applied current or potential?

I don‘t know where to start. Can someone suggest any good example?

Thank you!
5 Replies Last Post 2012年1月22日 GMT-5 04:16
Lasse Murtomäki
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2011年9月12日 GMT-4 07:44
Let say that you have concentration co in the oil phase and cw in the aqueous phase. Then at the boundary, use flux condition. Ion is transferring from water to oil:

In water: Inward flux = -Kp*(P*cw-co)
In oil. Inward flux = Kp*(P*cw-co)

where Kp is the permeability coefficient, for reversible transfer make it vary large, like 1000 cm/s.
P is the partition coefficient which depends on the potential

P = exp(zF/RT*(E(t)-E0))

and you have to define E(t) as a function. I use flc2hs function for in cyclic voltammetry. If you use an interpolated function (eg. triangle wave) Jacobian matrix fails in the corner point.

For example

E = Ei +v*t-2*flc2hs(t-ts,.0.001)*v*(t-ts)

Wish this replies your question
Let say that you have concentration co in the oil phase and cw in the aqueous phase. Then at the boundary, use flux condition. Ion is transferring from water to oil: In water: Inward flux = -Kp*(P*cw-co) In oil. Inward flux = Kp*(P*cw-co) where Kp is the permeability coefficient, for reversible transfer make it vary large, like 1000 cm/s. P is the partition coefficient which depends on the potential P = exp(zF/RT*(E(t)-E0)) and you have to define E(t) as a function. I use flc2hs function for in cyclic voltammetry. If you use an interpolated function (eg. triangle wave) Jacobian matrix fails in the corner point. For example E = Ei +v*t-2*flc2hs(t-ts,.0.001)*v*(t-ts) Wish this replies your question
Xu Zou
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2011年9月22日 GMT-4 17:22
Lasse. Thank you very much!
Lasse. Thank you very much!
Umar Ansari
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年1月19日 GMT-5 21:28
Hi Lasse

I am new to COMSOL I just wanted to to know which application mode I have to use to evaluate cyclic voltammetry. Secondly how and where to measure the current foe this model.

Umar
Hi Lasse I am new to COMSOL I just wanted to to know which application mode I have to use to evaluate cyclic voltammetry. Secondly how and where to measure the current foe this model. Umar
Lasse Murtomäki
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年1月20日 GMT-5 03:17
Application mode is Chemical species transport, and there Transport of diluted species (if they are diluted). Current is obtained in post-processing phase as a surface integral of the flux*n*F.
Application mode is Chemical species transport, and there Transport of diluted species (if they are diluted). Current is obtained in post-processing phase as a surface integral of the flux*n*F.
Umar Ansari
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年1月22日 GMT-5 04:16
Thanks Lasse it worked.
Thanks Lasse it worked.

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content