Menu

Discussion Forum

New Discussion
查找

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Current induced by a magnet

Posted 2011年10月25日 GMT-4 16:45 Low-Frequency Electromagnetics, Mesh Version 4.2a 2 Replies

Marco Fontana
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hi.
I'm really new to COMSOL Multiphysics and I think I need some help.
I have a single turn coil and a permanent magnet, same radius and parallels, in 3D. I know that moving the coil, i can change the magnetic field in the coil, and so i can obtain an induced current. But I don't know how to do this in COMSOL.

Moving the magnet depends on "moving mesh" (I think); so I put my magnet in "Free Deformation". Moving the magnet, the magnetic field (ploted in a 3D slice) doesn't move...Why? What's wrong? Otherwise, putting air and magnet in that node, the MF plotted moves too, but my magnet change its geometry.

I read various threads looking for a hint without succes.

I can also change my system using a MF time dependent. In this way nothing moves. But how can I evaluate the magnetic flux (B) and obtain a voltage? ( V=-d flux(B)/dt ) How many B involves my coil? Between them there is about 2/3cm.

I think it's a simple problem, but i read here ( www.comsol.se/community/forums/general/thread/18617/ ) that maybe this problem can't be solved using COMSOL.

Thanks in advance for any suggestions.

MF
2 Replies Last Post 2013年5月13日 GMT-4 12:02
Andrew Chou
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2011年10月25日 GMT-4 23:20
Hi everyone,

I'm facing some similar issues as well.

In my model, I have a permanent magnet (13.2 Tesla remanant flux density) moving back and forth and a fixed copper coil right next to it and I want to have the moving magnet induce a current and voltage into the fixed coil.

I initially based my model off of a CFD tutorial model for a fluid damper that has similar geometry to what I want and also uses the "Moving Mesh (ale)" module in order to move the damper piston (in my case, the magnet). I altered the tutorial model by removing the CFD physics and replacing it with MF physics and adding ampere's law to the magnet portion, as well as editing all the material properties. However, after running the simulation, I ran into some issues. With the fixed coil area part of the "Prescribed Deformation 1" for ale, I get a decent looking plot for the current density in that area (although I believe the values are a few orders of magnitude too large). If I don't select the fixed coil area as part as "Prescribed Deformation 1", I get a zero value for the current density in the coil. Is my approach to this problem correct?

Also, any suggestions on where I should put a cut point/line in the model to measure things going on in the coil (eg current density, electric field, etc)? Right now I'm using a cut point on the boundary between the coil and the magnet. My results change if I move the point just slightly to the right into the middle of the coil....

I'd like to attach the model file to clarify but the forum says its too big. What is the max size I can post and any tips on making my file smaller? I'm running 4.0a

Thanks!
-Andrew
Hi everyone, I'm facing some similar issues as well. In my model, I have a permanent magnet (13.2 Tesla remanant flux density) moving back and forth and a fixed copper coil right next to it and I want to have the moving magnet induce a current and voltage into the fixed coil. I initially based my model off of a CFD tutorial model for a fluid damper that has similar geometry to what I want and also uses the "Moving Mesh (ale)" module in order to move the damper piston (in my case, the magnet). I altered the tutorial model by removing the CFD physics and replacing it with MF physics and adding ampere's law to the magnet portion, as well as editing all the material properties. However, after running the simulation, I ran into some issues. With the fixed coil area part of the "Prescribed Deformation 1" for ale, I get a decent looking plot for the current density in that area (although I believe the values are a few orders of magnitude too large). If I don't select the fixed coil area as part as "Prescribed Deformation 1", I get a zero value for the current density in the coil. Is my approach to this problem correct? Also, any suggestions on where I should put a cut point/line in the model to measure things going on in the coil (eg current density, electric field, etc)? Right now I'm using a cut point on the boundary between the coil and the magnet. My results change if I move the point just slightly to the right into the middle of the coil.... I'd like to attach the model file to clarify but the forum says its too big. What is the max size I can post and any tips on making my file smaller? I'm running 4.0a Thanks! -Andrew
Mario Andres Kovacs
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2013年5月13日 GMT-4 12:02
Hi

Its a really late answer, but there is a good model in the comsol library:

www.comsol.com/showroom/gallery/14163/

good luck!
Mario


Hi Its a really late answer, but there is a good model in the comsol library: http://www.comsol.com/showroom/gallery/14163/ good luck! Mario

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content