Menu

Discussion Forum

New Discussion
查找

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Stress gradient

Posted 2010年1月11日 GMT+8 17:25 Version 4.2a 6 Replies

Andres Vasquez
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hello,
I am trying to simulate the deflection of a cantilever due to stress gradient, how can I define an uniform stress gradient through the cantilever thickness??
Thanks for your help!
Andres
6 Replies Last Post 2014年1月28日 GMT+8 04:32
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 2 decades ago 2010年1月14日 GMT+8 13:12
Hi

In V3.5a Structural module OR mems (smsld in 3D) (not the SLD standard multiphysics section) you can define directly your initial stress, and off you go.
i.e. Sx = STx*(z-z0) where Sx is the x component of the initial stress, z is the mesh coordinate and z0 the height of your neutral axis (for a beam shape deflection equivalent to a bending moment Mx

If you are stuck in SLD you would have to complete the equations to add the initial stress.

Try it out on a simple beam first, to you get full crontrol of your coordinate "transform" of the s tensor

Good luck
Ivar
Hi In V3.5a Structural module OR mems (smsld in 3D) (not the SLD standard multiphysics section) you can define directly your initial stress, and off you go. i.e. Sx = STx*(z-z0) where Sx is the x component of the initial stress, z is the mesh coordinate and z0 the height of your neutral axis (for a beam shape deflection equivalent to a bending moment Mx If you are stuck in SLD you would have to complete the equations to add the initial stress. Try it out on a simple beam first, to you get full crontrol of your coordinate "transform" of the s tensor Good luck Ivar
Andres Vasquez
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 2 decades ago 2010年1月14日 GMT+8 17:08
Hi,
Thanks a lot for your help!
I tried it that way and it worked fine.

Best regards,
Andres
Hi, Thanks a lot for your help! I tried it that way and it worked fine. Best regards, Andres
M M
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年5月18日 GMT+8 05:05
how can I apply stress gradient in 4.2a? This method doesn't work in 4.2a
how can I apply stress gradient in 4.2a? This method doesn't work in 4.2a
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年5月18日 GMT+8 22:41
Hi

why cant you apply stress as initial conditions in v4 ?
(you need to know the tensor form, not that trivial)

or easier just run a stationary load case to build up a natural stress, and then solve from there ?

--
Good luck
Ivar
Hi why cant you apply stress as initial conditions in v4 ? (you need to know the tensor form, not that trivial) or easier just run a stationary load case to build up a natural stress, and then solve from there ? -- Good luck Ivar
Alan Paterson
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2013年12月18日 GMT+8 23:14
I'm also having problems with stress gradients in 4.2A. I've done the calculations manually and the results of the model in no way resemble these calculations. I've attached my model to this post. The z-displacement for the calculated results I have should be approximately 0.127 microns for the 700um diameter sample (corresponds to a curvature of 2.083/m). Not 0.04 microns which I achieve from the model.

Is there something different about the way this initial stress is simulated now?
I'm also having problems with stress gradients in 4.2A. I've done the calculations manually and the results of the model in no way resemble these calculations. I've attached my model to this post. The z-displacement for the calculated results I have should be approximately 0.127 microns for the 700um diameter sample (corresponds to a curvature of 2.083/m). Not 0.04 microns which I achieve from the model. Is there something different about the way this initial stress is simulated now?

Attachments:

José Mauricio Urbano Caguasango
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2014年1月28日 GMT+8 04:32
Hi Ivar!

I am working on a linear static structural analysis. I want to perform an incremental analysis. I have a spherical pressure vessel with an interior pressure. My pressure vessel will deform. How do I perform a second analysis using as a starting point the last state of the previous stage (i.e. deformed stressed pressure vessel)?

Thanks in advance!
Mauricio
Hi Ivar! I am working on a linear static structural analysis. I want to perform an incremental analysis. I have a spherical pressure vessel with an interior pressure. My pressure vessel will deform. How do I perform a second analysis using as a starting point the last state of the previous stage (i.e. deformed stressed pressure vessel)? Thanks in advance! Mauricio

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content