Menu

Discussion Forum

New Discussion
查找

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Deformation of liquid droplet

Posted 2012年6月18日 GMT-4 16:29 Fluid & Heat, Microfluidics, Studies & Solvers Version 4.4 10 Replies

Chloe Wu
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

I am new to COMSOL, so I am referencing a work on deformation of liquid droplet impacting a solid surface. I tried to recreate the same model as that work. But I ran into several problems. As I tracked the steps taken by solver, at a certain time, the volume fraction of liquid would suddenly turn into 0.5 all over the domain. My result just doesn't seem right.

Also, I want to track the contact angle between liquid and solid surface, but I don't know how. Should I set up some new geometry?

Here is the link to the work I am referring to: www.comsol.com/papers/8116/

Attachment is my model. Please take a look at it and show me a right direction. I'm using version 4.3

Thank you!

Attachments:

10 Replies Last Post 2014年10月6日 GMT-4 08:49
Chloe Wu
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年6月19日 GMT-4 08:48
This is a simple model: 2-D axisymmetric, Laminar Two-Phase Flow, a water droplet falls down onto a solid surface due to gravity. I want to model the deformation process of the droplet after hitting to the ground. But my result is rather than dropping down to the ground and deformting, the droplet would suddenly spread all over the air domain.
This is a simple model: 2-D axisymmetric, Laminar Two-Phase Flow, a water droplet falls down onto a solid surface due to gravity. I want to model the deformation process of the droplet after hitting to the ground. But my result is rather than dropping down to the ground and deformting, the droplet would suddenly spread all over the air domain.
Muhammad Noman Hasan
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年8月22日 GMT-4 13:20
I am also trying to do something similar. there are some difficulties I am facing. I can simulate the impact and the water droplet spreads a little then the solution fails.

I can solve the problem when the droplet is falling from a few millimeter above the surface.

I also what to assign an initial velocity of the droplet but I couldn't can anyone help?

The model is based on COMSOL 3.5
I am also trying to do something similar. there are some difficulties I am facing. I can simulate the impact and the water droplet spreads a little then the solution fails. I can solve the problem when the droplet is falling from a few millimeter above the surface. I also what to assign an initial velocity of the droplet but I couldn't can anyone help? The model is based on COMSOL 3.5
Arthur Shoihet
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年10月3日 GMT-4 09:56
H
H
Shawn.F
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年10月19日 GMT-4 12:23
Hi everybody,

I have the exact same problem. I believe it has to be due to mesh and boundary conditions. I am trying to play with mesh and also implement different BCs.

If you have also found any way to get rid of this problem, I appreciate if you could share it with me.

Regards

Shawn
Hi everybody, I have the exact same problem. I believe it has to be due to mesh and boundary conditions. I am trying to play with mesh and also implement different BCs. If you have also found any way to get rid of this problem, I appreciate if you could share it with me. Regards Shawn
Shawn.F
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年10月19日 GMT-4 12:26

Hi everybody,

I have the exact same problem. I believe it has to be due to mesh and boundary conditions. I am trying to play with mesh and also implement different BCs.

If you have also found any way to get rid of this problem, I appreciate if you could share it with me.

Regards

Shawn
Hi everybody, I have the exact same problem. I believe it has to be due to mesh and boundary conditions. I am trying to play with mesh and also implement different BCs. If you have also found any way to get rid of this problem, I appreciate if you could share it with me. Regards Shawn
Arthur Shoihet
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年10月21日 GMT-4 12:22
H
H
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年10月21日 GMT-4 14:21
Hi

if you change the material you need to check both fluid nodes to set the right material to fluid1, as well as the interface to gas/liquide water air.

Furthermore, with the buble in contact with a surface, and with weting conditions, you have capilary forces that might be greater than the gravity forces, so I would recommend to leave the drop fully "flaoting" not initially in contact with any surface.

and I would use a p=0 point in one of the corner of the outer geometry, not attached to the initial droplet position

By the way, why not set wetting to all walls (wall1, and disable wall2&3) this works for me

Then your mesh is rather coarse, for a thin viscuouity fluid such as air this might be an issue


--
Good luck
Ivar
Hi if you change the material you need to check both fluid nodes to set the right material to fluid1, as well as the interface to gas/liquide water air. Furthermore, with the buble in contact with a surface, and with weting conditions, you have capilary forces that might be greater than the gravity forces, so I would recommend to leave the drop fully "flaoting" not initially in contact with any surface. and I would use a p=0 point in one of the corner of the outer geometry, not attached to the initial droplet position By the way, why not set wetting to all walls (wall1, and disable wall2&3) this works for me Then your mesh is rather coarse, for a thin viscuouity fluid such as air this might be an issue -- Good luck Ivar
Arthur Shoihet
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年10月25日 GMT-4 04:06
]
]
Richard Geist
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年11月18日 GMT-5 22:11
Change the transient initialization to phase initialization, due to the two-phase flow and the use of the level set method.

It is running for me at the moment, just waiting for results.
Change the transient initialization to phase initialization, due to the two-phase flow and the use of the level set method. It is running for me at the moment, just waiting for results.
Clare Knock
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 10 years ago 2014年10月6日 GMT-4 08:49
Hello,

I'm also trying to set up a similar problem to the following papers:

www.comsol.com/paper/deformation-behavior-of-a-liquid-droplet-impacting-a-solid-surface-8116

www.comsol.com/paper/solidification-of-a-liquid-metal-droplet-impinging-on-a-cold-surface-1492

I'm new to COMSOL and have a trial of 4.4 for another week, I'd like to see if I can get the problem set up before I buy the software. Can anyone give any advice as to how I can set up a droplet impacting a solid surface in COMSOL?

Thanks,
Raquel
Hello, I'm also trying to set up a similar problem to the following papers: http://www.comsol.com/paper/deformation-behavior-of-a-liquid-droplet-impacting-a-solid-surface-8116 http://www.comsol.com/paper/solidification-of-a-liquid-metal-droplet-impinging-on-a-cold-surface-1492 I'm new to COMSOL and have a trial of 4.4 for another week, I'd like to see if I can get the problem set up before I buy the software. Can anyone give any advice as to how I can set up a droplet impacting a solid surface in COMSOL? Thanks, Raquel

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content