Menu

Discussion Forum

New Discussion
查找

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

How to set different thermal conductivity in different direction?

Posted 2012年10月5日 GMT-4 01:08 Heat Transfer & Phase Change Version 4.3a 3 Replies

Xiang Qiu
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

I am trying to simulate a heat transfer model which includes layers with different thermal conductivity in X-Y direction and Z direction. Is it possible to assign a user defined material and have thermal conductivity as a vector? Any comments are appreciated.
3 Replies Last Post 2013年1月6日 GMT-5 04:28
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年10月5日 GMT-4 01:37
Hi

yes
but you must define an anisotropic "k", or check the physics node and select anisotropic material, it depends slightly in which physics you are

By default isotropic material is choosen and the scalar "k" of the material is distributed on the diagonal of the tensor k11, k22, k33
Also in the latest 4.3 version "material.k" is not even defined, you must chose "material.k11" or sqrt(material.k11^2+ ..) or whatever suits youre model

--
Good luck
Ivar
Hi yes but you must define an anisotropic "k", or check the physics node and select anisotropic material, it depends slightly in which physics you are By default isotropic material is choosen and the scalar "k" of the material is distributed on the diagonal of the tensor k11, k22, k33 Also in the latest 4.3 version "material.k" is not even defined, you must chose "material.k11" or sqrt(material.k11^2+ ..) or whatever suits youre model -- Good luck Ivar
Kamil Dursun
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2013年1月5日 GMT-5 10:15
Hello Ivar,
I have a similar question. I defined an anisotropic material in axi-symmetric 2 dimensions. What I get is a 2x2 array where I can fill in the values. However I am not sure which direction the k11, k12 etc. are.
I need to define one k for the r-direction and another for the z-direction.
I guess that k11 is the r-direction and k22 is the z-direction. Is this correct? What are k12 and k21 for?
Thank you for your reply.
Kamil
Hello Ivar, I have a similar question. I defined an anisotropic material in axi-symmetric 2 dimensions. What I get is a 2x2 array where I can fill in the values. However I am not sure which direction the k11, k12 etc. are. I need to define one k for the r-direction and another for the z-direction. I guess that k11 is the r-direction and k22 is the z-direction. Is this correct? What are k12 and k21 for? Thank you for your reply. Kamil
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2013年1月6日 GMT-5 04:28
Hi

to check the orientation, load your initial values of your model, and add a plot more coordinate and get your directions.

in 3D you can use the Definition coordinates to define your given orientation, in 2D and 2D-axi also but you should also consider the symmetries you are adding by a 2D or a 2D axi which reduces the DoF available.

normally 11 is along the first coordiante, 22 along the second etc

--
Good luck
Ivar
Hi to check the orientation, load your initial values of your model, and add a plot more coordinate and get your directions. in 3D you can use the Definition coordinates to define your given orientation, in 2D and 2D-axi also but you should also consider the symmetries you are adding by a 2D or a 2D axi which reduces the DoF available. normally 11 is along the first coordiante, 22 along the second etc -- Good luck Ivar

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content