Menu

Discussion Forum

New Discussion
查找

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Moddeling change in resistance/conductance due to thermal expansion

Posted 2014年6月26日 GMT-4 05:07 Low-Frequency Electromagnetics, Geometry, Mesh, Structural Mechanics Version 4.4 5 Replies

Rutger Stottelaar
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Dear Comsol users,

Due to temperature a material expands and when it does the electrical resistance of this material also changes. I want to model this in comsol.

I added the thermal expansion first, this gives results and the deformations can also be seen. Afterwards I want to calculate the resistance of this deformed structure and that is where it goes wrong. I cannot get different resistance values of different deformed structures.

I tried to add ALE afterwards but this does not seem to generate any results.

The model I attached is a very simplified model of what I am trying to create. However this is just to find out how the physics work in Comsol.

many thanks in advance for the help

Attachments:

5 Replies Last Post 2014年6月30日 GMT-4 05:41
Pieter Westerik
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2014年6月27日 GMT-4 03:42
Hi Rutger,

As far as I know, resistance changes caused by deformation are usually due to geometry changes rather than material properties changes. For exampe a strain gauge that is stretched becomes longer and, by the Poisson ratio, thinner, and by resistance = resistivity * length / {cross sectional area}, you find that the resistance increases, while the material propery (resistivity) remains the same.
Hi Rutger, As far as I know, resistance changes caused by deformation are usually due to geometry changes rather than material properties changes. For exampe a strain gauge that is stretched becomes longer and, by the Poisson ratio, thinner, and by resistance = resistivity * length / {cross sectional area}, you find that the resistance increases, while the material propery (resistivity) remains the same.
Rutger Stottelaar
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2014年6月27日 GMT-4 03:58
Dear Pieter,

You are correct. I formulated my sentence incorrectly.

Due to the expansion of the material the resistance of the geometry will increase. However, how do I model this in Comsol?
Dear Pieter, You are correct. I formulated my sentence incorrectly. Due to the expansion of the material the resistance of the geometry will increase. However, how do I model this in Comsol?
Pieter Westerik
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2014年6月27日 GMT-4 04:13
Sorry, I don't know.
Sorry, I don't know.
Henrik Sönnerlind COMSOL Employee

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2014年6月27日 GMT-4 07:29
Hi Rutger,

You do not need to add an ALE interface. You just have to switch on 'Include geometric nonlinearity' for the study step. Then the Electric Currents will see the deformed frame.

Regards,
Henrik
Hi Rutger, You do not need to add an ALE interface. You just have to switch on 'Include geometric nonlinearity' for the study step. Then the Electric Currents will see the deformed frame. Regards, Henrik
Rutger Stottelaar
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2014年6月30日 GMT-4 05:41
Dear Henrik,

Thank you for the advice, it seems to work!

Rutger
Dear Henrik, Thank you for the advice, it seems to work! Rutger

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content