Menu

Discussion Forum

New Discussion
查找

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Ill-conditioned preconditioner. Increase factor in error estimate to 18704635135.61623

Posted 2011年3月8日 GMT-5 08:12 Low-Frequency Electromagnetics, Fluid & Heat Version 4.0a, Version 4.2 6 Replies

Behrooz Rezaeealam
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hello

when i run my model, it gives me the solution, however i receive a warning too:
"Ill-conditioned preconditioner. Increase factor in error estimate to 18704635135.61623"
i would be grateful if anybody explain what it means.

Behrooz
6 Replies Last Post 2014年9月23日 GMT-4 04:18
COMSOL Moderator

Hello Behrooz Rezaeealam

Your Discussion has gone 30 days without a reply. If you still need help with COMSOL and have an on-subscription license, please visit our Support Center for help.

If you do not hold an on-subscription license, you may find an answer in another Discussion or in the Knowledge Base.

Tyler
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2011年5月31日 GMT-4 13:59
I'm also interested if any one has advice on this particular Warning
TT
I'm also interested if any one has advice on this particular Warning TT
Marjan
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2011年10月17日 GMT-4 08:56
Hi,

I also get such an error . In fact I am following a comsol example. In my case it is backstep laminar flow. It is strange. The results are exactly like what is expected as are shown in pdf model in the liberary but I get this error messege as well. Did you figure it out where it comes from?

Yours,
Marjan
Hi, I also get such an error . In fact I am following a comsol example. In my case it is backstep laminar flow. It is strange. The results are exactly like what is expected as are shown in pdf model in the liberary but I get this error messege as well. Did you figure it out where it comes from? Yours, Marjan
Santhosh Reddy
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2011年11月7日 GMT-5 11:32
Nobody has answer for this question?. I also got same error when solving laminar flow in a tube!.
Nobody has answer for this question?. I also got same error when solving laminar flow in a tube!.
Amir Fadel
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2011年11月7日 GMT-5 11:35
Hi,

It may due to the scaling of your variables, cehck the results and see whether imposing a Manual scaling value similar to the results you still get the error message.


Cheers
Hi, It may due to the scaling of your variables, cehck the results and see whether imposing a Manual scaling value similar to the results you still get the error message. Cheers
Santhosh Reddy
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2011年11月7日 GMT-5 12:37
Hi Amir,
Thanks for your reply. I get around that issue by changing the initial condition (instead of default value 0) to inlet velocity.
Hi Amir, Thanks for your reply. I get around that issue by changing the initial condition (instead of default value 0) to inlet velocity.
Ivelin Lyahtov
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2014年9月23日 GMT-4 04:18
Hey,

I'm new to comsol and I get the same warning. Please point out how you fixed this problem! Thanks in advance!

Regards,

Ivelin
Hey, I'm new to comsol and I get the same warning. Please point out how you fixed this problem! Thanks in advance! Regards, Ivelin

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content