Menu

Discussion Forum

New Discussion
查找

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Electrical Circuit in Electrostatic Simulation

Posted 2011年12月21日 GMT-5 09:50 Low-Frequency Electromagnetics, Parameters, Variables, & Functions, Studies & Solvers Version 4.2a 7 Replies

Thomas Schlegl
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hello!

Is it possible to have a electrical circuit problem connected with an electrostatics problem?
For example I want to connect a capacitor with a certain value to my electrostatics simulation.
If yes, how do I connect them, when my Terminal BC is defined in the electrostatics?

Thank you for your help...

Thomas
7 Replies Last Post 2013年7月7日 GMT-4 05:21
accelerate
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2011年12月21日 GMT-5 11:50
I got the same problem, I saw a paper mentioned using extrusion coupling and assmblies to do that.

--
learn COMSOL, like COMSOL
I got the same problem, I saw a paper mentioned using extrusion coupling and assmblies to do that. -- learn COMSOL, like COMSOL
Bhavin Pandya
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年4月11日 GMT-4 14:22
Hi Thomas,

Did you find a solution to the problem that you mentioned in this post. I am facing the same problem. I have a pressure sensor model which I want to couple to a front end circuit. Is there any way I could do that?

I appreciate your help.

Bhavin
Hi Thomas, Did you find a solution to the problem that you mentioned in this post. I am facing the same problem. I have a pressure sensor model which I want to couple to a front end circuit. Is there any way I could do that? I appreciate your help. Bhavin
Thomas Schlegl
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年4月12日 GMT-4 01:06
Hello!

I am sorry, but I could not solve this problem (with comsol).
Perhaps anyone else?

Thomas
Hello! I am sorry, but I could not solve this problem (with comsol). Perhaps anyone else? Thomas
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年4月12日 GMT-4 02:28
Hi

is it something like this you want to do ? I'm using the initial value on the circuit capacitor to discharge the capa into the COMSOL model

--
Good luck
Ivar
Hi is it something like this you want to do ? I'm using the initial value on the circuit capacitor to discharge the capa into the COMSOL model -- Good luck Ivar

Attachments:

Thomas Schlegl
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年4月13日 GMT-4 03:42
Hello!

Thank you for the fast answer. It is similar to what I was lookin for, but I don't understand it completley.
What happens with the init-value of the capa?
The simulation acts like one would switch on 10V even if it says 10V init value?
For example, how do I get a real init value for the capa?

Thanks again for your answers...

Thomas!
Hello! Thank you for the fast answer. It is similar to what I was lookin for, but I don't understand it completley. What happens with the init-value of the capa? The simulation acts like one would switch on 10V even if it says 10V init value? For example, how do I get a real init value for the capa? Thanks again for your answers... Thomas!
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2012年4月13日 GMT-4 11:37
Hi

my capa is very large compared to the one in the model, if you put a one pf capa the voltage should drop, test it out ;)

--
Good luck
Ivar
Hi my capa is very large compared to the one in the model, if you put a one pf capa the voltage should drop, test it out ;) -- Good luck Ivar
Vito Di Virgilio
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2013年7月7日 GMT-4 05:21
Hello everybody.


I have a quite similar problem, I would like to charge a capacitor with a current source of 25mA and compliance of 70V. So when the capa is charged, the voltage drops to 0. How can I simulate this using the CIR module?

Have a nice day!
Hello everybody. I have a quite similar problem, I would like to charge a capacitor with a current source of 25mA and compliance of 70V. So when the capa is charged, the voltage drops to 0. How can I simulate this using the CIR module? Have a nice day!

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content