Menu

Discussion Forum

New Discussion
查找

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

High Viscosity in Two Phase Flow

Posted 2012年9月30日 GMT-4 22:55 Computational Fluid Dynamics (CFD), Microfluidics, Materials, Studies & Solvers Version 4.3a 2 Replies

Cyrus Beh
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hi,

I have constructed a two-phase flow model, using the "Droplet Breakup in a T-Junction" model in the gallery. I managed to compute the default model successfully. However, when I change the viscosity of the two solutions to a system I am actually interested in (Viscosity phase 1 = 27.64mPa.s, Viscosity phase 2 = 994mPa.s) the model simply does not compute well (time steps are extremely small, making it impractical for solution). I wonder what other parameters in the model I can change to expedite the solution. I am pretty sure that there is something wrong with my model (solver parameters, perhaps?) but I am not very familiar with Comsol. Can anyone give me some suggestions? Thanks!
2 Replies Last Post 2013年4月24日 GMT-4 11:23
COMSOL Moderator

Hello Cyrus Beh

Your Discussion has gone 30 days without a reply. If you still need help with COMSOL and have an on-subscription license, please visit our Support Center for help.

If you do not hold an on-subscription license, you may find an answer in another Discussion or in the Knowledge Base.

Alex Morgan
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2013年4月24日 GMT-4 10:42
Hi,

I am having exactly the same problem. I'm trying to simulate droplet production in a device that I know does work. I'm using this design to work out how to do simulations in Comsol, so that I can then use the same parameters etc. to do simulations of other designs (before I actually make them). I've changed the densities and viscosities, interfacial tension and contact angle to known values. I get some sort of droplet production initially, but it takes a really long time (2-3days) and after about 75%, the simulation fails.
Does anyone have any advice?

Thanks
Hi, I am having exactly the same problem. I'm trying to simulate droplet production in a device that I know does work. I'm using this design to work out how to do simulations in Comsol, so that I can then use the same parameters etc. to do simulations of other designs (before I actually make them). I've changed the densities and viscosities, interfacial tension and contact angle to known values. I get some sort of droplet production initially, but it takes a really long time (2-3days) and after about 75%, the simulation fails. Does anyone have any advice? Thanks
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2013年4月24日 GMT-4 11:23
Hi

I'm also stuck here: I have (simply) a water droplet falling in air in "phase set" mode:

without the consevative laws on my droplet disolves rapidly (butit solves nicely so long it exist),

with conservative laws on the droplet persist, but rapidly the solver steps comes down to some 1e-18 sec, which is really not usefull when I need some 0.2 sec at least total solver time.

It solves rapidly in "level set", but I cannot use "moving wetting walls" nor "contact physics work options" in "level set", these are only defined in "two flow phase set" method

For those who have some ideas which button to tweak, pls come with your suggestions ;)

--
Good luck
Ivar
Hi I'm also stuck here: I have (simply) a water droplet falling in air in "phase set" mode: without the consevative laws on my droplet disolves rapidly (butit solves nicely so long it exist), with conservative laws on the droplet persist, but rapidly the solver steps comes down to some 1e-18 sec, which is really not usefull when I need some 0.2 sec at least total solver time. It solves rapidly in "level set", but I cannot use "moving wetting walls" nor "contact physics work options" in "level set", these are only defined in "two flow phase set" method For those who have some ideas which button to tweak, pls come with your suggestions ;) -- Good luck Ivar

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content