科技论文和演示页面包括了 COMSOL 全球用户年会上所有的用户演示文稿。这些演示文稿介绍了 COMSOL 用户是如何使用 COMSOL Multiphysics 进行创新性研究和产品设计,研究主题涵盖了包括电气、机械、流体和化工等范围广泛的行业和应用领域。您可以使用“快速搜索”来查找与您研究领域相关的演示文稿。

A COMSOL Model of Damage Evolution Due to High Energy Laser Irradiation of Partially Absorptive Materials

P. Joyce[1], J. Radice[1], A. Tresansky[1], J. Watkins[1]
[1]United States Naval Academy, Annapolis, MD, USA

In this paper we present a transient numerical model of the heat transfer and thermochemical damage evolution in an IR translucent material using ...

Irrotational Motion of an Incompressible Fluid Past a Wing Section in an Unbounded Region

J. Russell[1]
[1]Florida Institute of Technology, Melbourne, FL, USA

Developers of numerical models who address the title problem face several hurdles, such as: (1), the need to formulate boundary conditions applicable ...

Towards Rotordynamic Analysis with COMSOL Multiphysics

M. Karlsson[1]
[1]ÅF, Stockholm, Sweden

In this paper a pre-study on using COMSOL Multiphysics for rotordynamic analysis is presented. It is concluded that it is possible to use COMSOL ...

Modeling Internal Heating of Optoelectronic Devices Using COMSOL

N. Brunner[1][,][2]
[1]Voxtel, Inc, Beaverton, OR, USA
[2]University of Oregon, Eugene, OR, USA

In this paper the heat transfer module in COMSOL is utilized to simulate internal heating of an Avalanche Photodiode due to light-induced current ...

Modeling of Chloride Transport in Cracked Concrete: a 3-D Image–Based Microstructure Simulation

Y. Lu[1], E. Garboczi[1], D. Bentz[1]
[1]National Institute of Standards and Technology, Gaithersburg, MD, USA

The prediction of concrete materials service life is not easy, because the complex heterogeneous microstructure and the random nature of concrete ...

Modeling and Prediction of Line Pattern Collapse

D. Bassett[1], M. Carcasi[1], W. Printz[1]
[1]Tokyo Electron America, Austin, TX, USA

In semiconductor manufacturing, effective cleaning of structures with liquid is one of the most important and potentially difficult process steps. It ...

Steps for the Optimization of Pipe and Tubing Extrusion Dies

J.R. Puentes[1], T.A. Osswald[1], S. Schick[2], J. Berg[2]
[1]Polymer Engineering Center, University of Wisconsin, Madison, WI, USA
[2]TEEL Plastics, Baraboo, WI, USA

The extrusion of polyolefin pipes suffers degradation due to mechanical design problems of the extrusion die that is commonly used. This study uses ...

Modeling of DC Discharges in Argon at Low Pressures

V. Gorokhovsky[1]
[1]Vapor Technologies, Inc., Longmont, CO, USA

The glow discharges in argon at pressures of 1 to 20 mTorr are modeling using COMSOL Plasma Module. DC glow discharge with secondary electron emission ...

Natural Convection Driven Melting of Phase Change Material: Comparison of Two Methods

D. Groulx[1], F. Samara[1], P.H. Biwole[2]
[1]Department of Mechanical Engineering, Dalhousie University, Halifax, NS, Canada
[2]Department of Mathematics and Interactions, University of Nice Sophia-Antipolis, Nice, France

Design of latent heat energy storage systems (LHESS) requires knowledge of heat transfer processes within them, as well as the phase change behavior of ...

Modeling Proton Transport in Hydrophobic Polymeric Electrolytes

M. Andrews[1]
[1]Caribbean Industrial Research Institute, Calibration Laboratory, University of the West Indies, St. Augustine, Trinidad and Tobago

The Polymer Electrolyte Membrane fuel cell is one of the most promising green technologies for addressing portable, as well as transportation power ...