论文和技术资料

快速搜索

技术资料

白皮书

了解多物理场仿真在基础研究和产品设计中的应用

各个行业的工程师和科研人员都在使用多物理场仿真来研发创新的产品设计和流程。他们在 COMSOL 用户年会上展示了丰富的技术论文和演示文稿，您可以从他们的研究成果中寻找灵感。

使用左侧【快速搜索】工具查找您感兴趣的研究，或按照应用领域进行筛选。

查看 COMSOL 用户年会 2024 论文

搜索：

High-Resolution FSI Modeling of a High-Aspect Ratio Involute Flow Channel in the HFIR at ORNL

A. I. Elzawawy [1], J. D. Freels [2], F. G. Curtis [2, 3],
[1] Vaughn College of Aeronautics and Technology, East Elmhurst, NY, USA
[2] Oak Ridge National Laboratory, Oak Ridge, TN, USA
[3] University of Tennessee, Knoxville, TN, USA

The high flow rate within the HFIR cooling water flow channel causes the fuel plates to deflect which in ... 扩展阅读

Transport Phenomena and Shrinkage Modeling During Convective Drying of Vegetables

S. Curcio[1] and M. Aversa[1]
[1]Department of Engineering Modeling, University of Calabria, Arcavacata di Rende, CS, Italy

The aim of the present work is the formulation of a theoretical model describing the transport phenomena ... 扩展阅读

Heat Loss Evaluation of an Experimental Set-up for Predicting the Initial Stage of the Boiling Curve for Water at low Pressure

K. T. Witte[1], F. Dammel[2], L. Schnabel[1], and P. Stephan[2]
[1]Fraunhofer Institut Solare Energiesysteme - Department of Thermal Systems and Buildings, Freiburg, Germany
[2]Technische Universität Darmstadt - Institute of Technical Thermodynamics, Darmstadt, Germany

In this paper heat losses and gains are assessed for a specific measuring set-up improving the validity of ... 扩展阅读

CFD/Electromagnetics Interactions via Realistic Heat and Mass Transfer to Moist Substrates

G. Ruocco[1], M. V. De Bonis[2]
[1]Engineering College, University of Basilicata, Potenza, Italy
[2]Institute of Food Science and Production, National Research Council, Bari, Italy

Localized convection heat and mass transfer can be intensified and optimized by providing exposure to ... 扩展阅读

Design, Fabrication and Simulation of Microchannel Network for MEMS

V. Jain[1], A. K. Sharma[2], P. Kumar[2]
[1]Thapar University, Patiala, Punjab, India
[2]Indian Institute of Technology Roorkee, Roorkee, Uttar Pradesh, India

The greatest challenge being faced for realization of Micro-Electro Mechanical System (MEMS) technology is ... 扩展阅读

The Fast Model for Ionic Wind Simulation

A. Samusenko[1], Yu. Stishkov[1], P. Zhidkova[1]
[1]Saint Petersburg State University, Research and Educational Center “Electrophysics”, St Petersburg, Russia

Ionic wind is the gas flow induced by the corona discharge. Ions produced by corona are accelerated by ... 扩展阅读

Numerical Analysis of Mass Transfer Rate in Droplet Flow at Microscopic Scales

S. Cito[1], T. Sikanen[1]
[1]Division of Pharmaceutical Chemistry and Technology, Faculty of Pharmacy, University of Helsinki, Helsinki, Finland

Droplet flow at microscopic scale is often used to enhance many pharmaceuticals and industrial processes (i ... 扩展阅读

Numerical Simulation of Concentration Polarization to Estimate Gypsum and Calcium Carbonate Scaling on Membrane Surfaces

A. Santafé-Moros[1], J.M. Gozálvez-Zafrilla[1]
[1]Institute for Industrial, Radiophysical and Environmental Safety (ISIRYM) - Universitat Politècnica de Valencia, Valencia, Spain

This paper shows a model to estimate the scaling parameters for reverse osmosis membrane processes. The model ... 扩展阅读

Numerical Simulations Demonstrate Safe Vitrification and Warming of Embryos Using the Rapid-i™ Device

B.O.J. Johansson[1][2], Y.A. Tarakanov[1], H.J. Lehmann[2], and S.P. Apell[1]

[1]Department of Applied Physics, Chalmers University of Technology, Gothenburg, Sweden
[2]Vitrolife Sweden AB, Västra Frölunda, Sweden

During cryopreservation of human embryos, ice crystal formation in the embryos or in surrounding media may ... 扩展阅读

Numerical Aspects of the Implementation of Artificial Boundary Conditions for Laminar Fluid-Structure Interactions

C. Boeckle[1], P. Wittwer[1]
[1]University of Geneva, Geneva, Switzerland

We discuss the implementation of artificial boundary conditions for stationary Navier-Stokes flows past ... 扩展阅读

第一页

341–350 of 524

最后一页