科技论文和演示页面包括了 COMSOL 全球用户年会上所有的用户演示文稿。这些演示文稿介绍了 COMSOL 用户是如何使用 COMSOL Multiphysics 进行创新性研究和产品设计,研究主题涵盖了包括电气、机械、流体和化工等范围广泛的行业和应用领域。您可以使用“快速搜索”来查找与您研究领域相关的演示文稿。
COMSOL-News-Magazine-2017
COMSOL-News-Magazine-2017-Special-edition-acoustics
COMSOL-News-Magazine-2016

Material Selection and Computational Analysis on DOHC V16 Engine’s Mounting Bracket Using COMSOL Multiphysics

M. V. A. Nag[1]
[1]G.R.I.E.T., Hyderabad, AP, India

Reduction of the engine vibration and the dynamic forces transmitting from engine to the automotive body structure has always been an important part of ...

Numerical and Experimental Study of a Concentrated Indentation Force on Polymer Matrix Composites

V. Antonucci[1][2], M. Esposito[1], R. Marzella[2], and M. Giordano[1][2]
[1]Institute for Composite and Biomedical Materials, CNR, Portici, NA, Italy
[2]Imast, Portici, NA, Italy

A quasi static indentation test on a laminate composite has been investigated numerically and experimentally. In particular, the test has been ...

Introduction to COMSOL based Modeling of Levitated Flywheel Rotor

A. Pilat
AGH University of Science and Technology
Kraków, Poland

This elaboration presents a pre-study on automatic rotor construction for the flywheel energy storage system dedicated to operate in the levitation ...

Simulation of the Thermal Expansion of an Inductively Heated Gear Wheel for Shrink Fitting Purposes

C. Hollenbeck [1], Z. Jildeh [1], T. Rydlewski [1], P. Kirchner [1],
[1] Imagine Engineering GmbH, Bergheim, Germany

Due to the advantages of induction heating as a method for precise and efficient local heating, it is perfectly suited for thermal shrink fitting of a ...

Determination of the Fundamental Resonant Modes of a Polysilicon H-Beam Using COMSOL Multiphysics® Software

T. Thomas[1], M. Sundaram[1], R. Bejam[1]
[1]Birla Institute of Technology and Science, Pilani - Pilani Campus, Rajasthan, India

A Polysilicon H-beam is a micro-machined structure consisting of two primary members connected by a third member of much lower width and much greater ...

Modeling the Buckling of Isogrid Plates

E. Gutierrez-Miravete[1], and J. Lavin[2]
[1]Rensselaer at Hartford, Hartford, CT, USA
[2]UTC-Pratt & Whitney, East Hartford, CT, USA

Isogrid plate components are widely used in aerospace structures because of their greater stiffness to weight ratios compared with thicker plates of ...

Design and Optimization of Highly Sensitive Single Axis Accelerometer using COMSOL Multiphysics®

Kunal A.Kshirsagar[1], K.Govardhan[1],
[1]VIT University, Sensor System Technology, School of Electronics Engineering, Vellore, Tamil Nadu, India
[2]VIT University, MEMS & Sensor Division, School of Electronics Engineering, Vellore, Tamil Nadu, India

Accelerometers are successfully commercialized MEMS devices. COMSOL Multiphysics® has been used in the modeling, simulation and optimizing of this ...

Structural Optimization of the AISHa Ion Source - new

F. Noto[1], M. Piscopo[1], L. Celona[1], D. Cittadino[1], S. Gammino[1], G. Cuttone[1], G. Gallo[1], G. Schillaci[1], C. Campisano[2], L. Lo Nigro[3], G. Costa[3], A. Campisano[4]
[1]Laboratorio Nazionale del Sud, Santa Sofia, Catania, Italy
[2]Gravina di Catania, Sicily, Italy
[3]Trinacria, Canalicchio, Catania, Italy
[4]Unico Informatica, li Battiati, Catania, Italy

Different facilities for hadrontherapy have been built in the recent past. AISHa ion source has been designed by keeping in mind the typical ...

Optimization of Mechanical Properties of Superconducting Cavities for Project X LINAC

I. Gonin[1], M. Awida[1], T. Khabiboulline[1], V. Yakovlev[1]
[1]Fermilab, Batavia, IL, USA

Project X is a proposed proton accelerator complex at Fermilab. The CW LINAC is based on five types of resonators operating at three frequencies: half ...

A Simplified Approach to the Contact in Thermo-mechanical Analysis of Refractory Linings

Y. Kaymak
VDEh Betriebsforschungsinstitut GmbH
Düsseldorf, Germany

The geometrical design and material choice for a refractory lining requires a good understanding of its thermo-mechanical behavior. Design engineers ...