Menu

Discussion Forum

New Discussion
查找

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Material properties

Posted 2011年12月8日 GMT-5 06:11 MEMS & Nanotechnology, MEMS & Piezoelectric Devices Version 4.2 3 Replies

Jürgen Gluch
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hello

today I noticed that my material copper has the properties "Electric conductivity | sigma | 5.998[S/m]" and "Reference resitivity | rho0 |1.72e8[Ohm*m]" as well as the temperature coefficient alpha. Why two values, because sigma = 1/rho0 , isn't it?
How can I check which physics uses which value, or how can I assign sigma = 1/rho0*(1+alpha*DeltaT)?

greetings
Jürgen Gluch
3 Replies Last Post 2011年12月14日 GMT-5 09:01
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2011年12月9日 GMT-5 01:02
Hi

in V4 you have the "vue" for the active properties, and then you need to go through the equations in detail to see where and when some are used (tedious) mostly the doc covers this too, but the info is scattered around ;)

--
Good luck
Ivar
Hi in V4 you have the "vue" for the active properties, and then you need to go through the equations in detail to see where and when some are used (tedious) mostly the doc covers this too, but the info is scattered around ;) -- Good luck Ivar
Magnus Ringh COMSOL Employee

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2011年12月9日 GMT-5 03:07
Hi,

The reference resistivity rho0 is used for exactly the linearized resistivity sigma = 1/rho0*(1+alpha*DeltaT) that you mention, which is a predefined option ("Linearized resistivity") in the Current Conservation settings for the Electric Currents interface.

In the Copper node under Materials (and any other materials that you use), green check marks indicate the material properties that are used by the physics interfaces in the model. So, in an Electric Currents model, if you use "From material" to specify the electrical conductivity, the following material properties are used:

Electrical conductivity sigma
Relative permittivity epsilonr (for the constitutive relation)

If you instead use "Linearized resistivity" to specify the electrical conductivity, the following material properties are used:

Relative permittivity epsilonr
Reference resistivity rho0
Resistivity temperature coefficient alpha
Reference temperature Tref

Best regards,
Magnus Ringh, COMSOL
Hi, The reference resistivity rho0 is used for exactly the linearized resistivity sigma = 1/rho0*(1+alpha*DeltaT) that you mention, which is a predefined option ("Linearized resistivity") in the Current Conservation settings for the Electric Currents interface. In the Copper node under Materials (and any other materials that you use), green check marks indicate the material properties that are used by the physics interfaces in the model. So, in an Electric Currents model, if you use "From material" to specify the electrical conductivity, the following material properties are used: Electrical conductivity sigma Relative permittivity epsilonr (for the constitutive relation) If you instead use "Linearized resistivity" to specify the electrical conductivity, the following material properties are used: Relative permittivity epsilonr Reference resistivity rho0 Resistivity temperature coefficient alpha Reference temperature Tref Best regards, Magnus Ringh, COMSOL
Jürgen Gluch
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2011年12月14日 GMT-5 09:01
Thanks for the explanation. I find it sometimes really difficult to understand the implementation and where which input is used. Maybe a context related search function would help the user in such situations.

Jürgen
Thanks for the explanation. I find it sometimes really difficult to understand the implementation and where which input is used. Maybe a context related search function would help the user in such situations. Jürgen

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content