Menu

Discussion Forum

New Discussion
查找

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

problem with geometry & draw reflectinn spectrum of gating wave guide

Posted 2013年3月7日 GMT-5 02:35 RF & Microwave Engineering Version 4.4 4 Replies

Sara Kian
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hi,

I am trying to simulate Bragg grating in SOI waveguide(attached to the massage) but I have a problem with drawing the geometry:
First: the horizontal scale is much larger than the vertical one so I can't draw it.

Second: I am not sure if I should draw the top-view of the grating in comsol like Fig.1 in paper.
Third : I don;t know which part of the comsol can help me to draw reflection & transmissin spectra of the waveguide.I guess S-parameter can help me but I dont know how I can apply source and which boundary conditions I should use.
Should I use RF module> In-plane wave > Te mode> harmonic ?

Thanks in advance,

Sara
4 Replies Last Post 2014年10月30日 GMT-4 09:27
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2013年3月7日 GMT-5 07:36
Hi

also in 3.5 there was a way to change the geoemtric view such to not scale X-Y axis equal, useful for very different scale models, such as MEMS

--
Good luck
Ivar
Hi also in 3.5 there was a way to change the geoemtric view such to not scale X-Y axis equal, useful for very different scale models, such as MEMS -- Good luck Ivar
Sara Kian
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2013年3月7日 GMT-5 08:52
Hi,
Thanks for help , how about appying source ,comsol consider incident wave as "exp(-j*k0_rfwe*x)" is that enough to apply this field to a port in order to have source?

Best Regards,
Sara
Hi, Thanks for help , how about appying source ,comsol consider incident wave as "exp(-j*k0_rfwe*x)" is that enough to apply this field to a port in order to have source? Best Regards, Sara
Sara Kian
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2013年3月7日 GMT-5 10:03
Hi,

I have a problem with inport , the check box " wave exitation at this port" is inactive, why? what should I do?

Thanks,

sara
Hi, I have a problem with inport , the check box " wave exitation at this port" is inactive, why? what should I do? Thanks, sara
晓妹 孙
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 2014年10月30日 GMT-4 09:27

Hi,

I have a problem with inport , the check box " wave exitation at this port" is inactive, why? what should I do?

Thanks,

sara


Hi , i encounterd the same problem, can U share the solution with me?
Thank U very much.
[QUOTE] Hi, I have a problem with inport , the check box " wave exitation at this port" is inactive, why? what should I do? Thanks, sara [/QUOTE] Hi , i encounterd the same problem, can U share the solution with me? Thank U very much.

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content